Browsing by Subject "supercritical carbon dioxide"
Now showing 1 - 2 of 2
Results Per Page
Sort Options
Item A Computational Study on the Thermal-Hydraulic Behavior of Supercritical Carbon Dioxide in Various Printed Circuit Heat Exchanger Designs(2013-02-04) Matsuo, BryceThere has been an ever-increasing demand for power generation, which is predicted to grow as society becomes more advanced. However, tradition fossil fuels are beginning to deplete, and there is a great necessity for alternative fuel sources that will bridge the gap between energy production and consumption. To decrease the high demand alternative fuel sources are gaining in popularity. The supercritical carbon dioxide Brayton power cycle has been proposed as a possible cycle for nuclear and concentrated solar power generation. Two main advantages of having supercritical carbon dioxide are the large property variations and component size associated with power cycle. Forced convection heat transfer of supercritical carbon dioxide in printed circuit heat exchanger geometries were investigated in the following study using a finite volume framework and the FLUENT 12.1 code. The geometries of interest were: non- chamfered zig-zag, chamfered zig-zag, and air foil. Flow through the three geometries was in the horizontal orientation and subject to a heating mode operation. A range of testing conditions were explored, including operating pressures between 7.5 to 10.2 MPa with the mass flux ranging from 326 to 762 kg/m2-s. Due to the turbulent nature of this problem, the k?E with enhanced wall treatment and shear stress transport k?? turbulence models were considered. With this addition a total of 54 simulations were performed. Results indicated that there was an increase in the heat transfer coefficient as the supercritical carbon dioxide reached the pseudocritical temperature, conversely as there was an increase in operating pressure, the heat transfer coefficient decreased. Nevertheless, this increase near the pseudocritical temperature was due to a sharp increase in the specific heat. Mass flux effects indicated that there was an increase in heat transfer as the mass flux was increased. This was due to the increase in Reynolds number near the pseudocritical temperature. Next, pressure losses were investigated for the three geometries. The non-chamfered zig-zag channel had the greatest pressure loss associated with it, while the air foil channel had the least. Based on the results, the ratio of the friction factor to heat transfer for the non-chamfered and chamfered zig-zag geometries were approximately 2.65 and 1.57 times higher than for the air foil, thus leading to the idea that the air foil channel may be best suited for practical applications. Finally, the simulation results were compared to experimental data and existing correlations. Many existing correlations failed to accurately predict the magnitude of heat transfer, although they exhibited a similar trend. A new correlation was developed for the zig-zag geometries based on the numerical data obtained during this investigation and published experimental data. The new correlation is able to predict the maximum heat transfer coefficient within 12.4%.Item Experimental and simulation studies of sequestration of supercritical carbon dioxide in depleted gas reservoirs(Texas A&M University, 2004-09-30) Seo, Jeong Gyuhe feasibility of sequestering supercritical CO2 in depleted gas reservoirs. The experimental runs involved the following steps. First, the 1 ft long by 1 in. diameter carbonate core is inserted into a viton Hassler sleeve and placed inside an aluminum coreholder that is then evacuated. Second, with or without connate water, the carbonate core is saturated with methane. Third, supercritical CO2 is injected into the core with 300 psi overburden pressure. From the volume and composition of the produced gas measured by a wet test meter and a gas chromatograph, the recovery of methane at CO2 breakthrough is determined. The core is scanned three times during an experimental run to determine core porosity and fluid saturation profile: at start of the run, at CO2 breakthrough, and at the end of the run. Runs were made with various temperatures, 20?C (68?F) to 80?C (176?F), while the cell pressure is varied, from 500 psig (3.55 MPa) to 3000 psig (20.79 MPa) for each temperature. An analytical study of the experimental results has been also conducted to determine the dispersion coefficient of CO2 using the convection-dispersion equation. The dispersion coefficient of CO2 in methane is found to be relatively low, 0.01-0.3 cm2/min.. Based on experimental and analytical results, a 3D simulation model of one eighth of a 5-spot pattern was constructed to evaluate injection of supercritical CO2 under typical field conditions. The depleted gas reservoir is repressurized by CO2 injection from 500 psi to its initial pressure 3,045 psi. Simulation results for 400 bbl/d CO2 injection may be summarized as follows. First, a large amount of CO2 is sequestered: (i) about 1.2 million tons in 29 years (0 % initial water saturation) to 0.78 million tons in 19 years (35 % initial water saturation) for 40-acre pattern, (ii) about 4.8 million tons in 112 years (0 % initial water saturation) to 3.1 million tons in 73 years (35 % initial water saturation) for 80-acre pattern. Second, a significant amount of natural gas is also produced: (i) about 1.2 BSCF or 74 % remaining GIP (0 % initial water saturation) to 0.78 BSCF or 66 % remaining GIP (35 % initial water saturation) for 40-acre pattern, (ii) about 4.5 BSCF or 64 % remaining GIP (0 % initial water saturation) to 2.97 BSCF or 62 % remaining GIP (35 % initial water saturation) for 80-acre pattern. This produced gas revenue could help defray the cost of CO2 sequestration. In short, CO2 sequestration in depleted gas reservoirs appears to be a win-win technology.