Browsing by Subject "distillation"
Now showing 1 - 3 of 3
Results Per Page
Sort Options
Item Biofuels from Corn Stover: Pyrolytic Production and Catalytic Upgrading Studies(2013-01-15) Capunitan, Jewel AlviarDue to security issues in energy supply and environmental concerns, renewable energy production from biomass becomes an increasingly important area of study. Thus, thermal conversion of biomass via pyrolysis and subsequent upgrading procedures were explored, in an attempt to convert an abundant agricultural residue, corn stover, into potential bio-fuels. Pyrolysis of corn stover was carried out at 400, 500 and 600oC and at moderate pressure. Maximum bio-char yield of 37.3 wt.% and liquid product yield of 31.4 wt.% were obtained at 400oC while the gas yield was maximum at 600oC (21.2 wt.%). Bio-char characteristics (energy content, proximate and ultimate analyses) indicated its potential as alternative solid fuel. The bio-oil mainly consisted of phenolic compounds, with significant proportions of aromatic and aliphatic compounds. The gas product has energy content ranging from 10.1 to 21.7 MJ m-3, attributed to significant quantities of methane, hydrogen and carbon dioxide. Mass and energy conversion efficiencies indicated that majority of the mass and energy contained in the feedstock was transferred to the bio-char. Fractional distillation of the bio-oil at atmospheric and reduced pressure yielded approximately 40-45 wt.% heavy distillate (180-250oC) with significantly reduced moisture and total acid number (TAN) and greater energy content. Aromatic compounds and oxygenated compounds were distributed in the light and middle fractions while phenolic compounds were concentrated in the heavy fraction. Finally, hydrotreatment of the bio-oil and the heavy distillate using noble metal catalysts such as ruthenium and palladium on carbon support at 100 bar pressure, 4 hours reaction time and 200o or 300oC showed that ruthenium performed better at the higher temperature (300oC) and was more effective than palladium, giving about 25-26% deoxygenation. The hydrotreated product from the heavy distillate with ruthenium as catalyst at 300oC had the lowest oxygen content and exhibited better product properties (lower moisture, TAN, and highest heating value), and can be a potential feedstock for co-processing with crude oils in existing refineries. Major reactions involved were conversion of phenolics to aromatics and hydrogenation of ketones to alcohols. Results showed that pyrolysis of corn stover and product upgrading produced potentially valuable sources of fuel and chemical feedstock.Item Experimental and analytical studies of hydrocarbon yields under dry-, steam-, and steam with propane-distillation(Texas A&M University, 2004-09-30) Ramirez Garnica, Marco AntonioRecent experimental and simulation studies -conducted at the Department of Petroleum Engineering at Texas A&M University - confirm oil production is accelerated when propane is used as an additive during steam injection. To better understand this phenomenon, distillation experiments were performed using seven-component synthetic oil consisting of equal weights of the following alkanes: n-C5, n-C6, n-C7, n-C8, n-C9, nC10, and n-C15. For comparison purposes, three distillation processes were investigated: dry-, steam-, and steam-propane-distillation, the latter at a propane:steam mass ratio of 0.05. The injection rate of nitrogen during dry-and steam-distillation was the same as that of propane during steam-propane distillation, 0.025 g/min, with steam injection rate kept at 0.5 g/min. The distillation temperatures ranged from 115?C to 300?C and were increased in steps of 10?C. The cell was kept at each temperature plateau (cut) for 30 minutes. Distillation pressures ranged from 0 psig for dry distillation to 998 psig for steam-and steam-propane distillation. The temperature-pressure combination used represented 15?C superheated steam conditions. Distillate samples were collected at each cut, and the volume and weight of water and hydrocarbon measured. In addition, the composition of the hydrocarbon distillate was measured using a gas chromatograph. Main results of the study may be summarized as follows. First, the hydrocarbon yield at 125?C is highest with steam-propane distillation (74 wt%) compared to steam distillation (58 wt%), and lowest with dry distillation (36 wt%). This explains in part the oil production acceleration observed in steam-propane displacement experiments. Second, the final hydrocarbon yield at 300?C however is the same for the three distillation processes. This observation is in line with the fact that oil recoveries were very similar in steam- and steam-propane displacement experiments. Third, based on the yields of individual hydrocarbon components, steam-propane distillation lowers the apparent boiling points of the hydrocarbons significantly. This phenomenon may be the most fundamental effect of propane on hydrocarbon distillation, which results in a higher yield during steam-propane distillation and oil production acceleration during steam-propane displacement. Fourth, experimental K-values are higher in distillations with steam-propane for the components n-hexane, n-heptane, n-octane, and n-nonane. Fifth, vapor fugacity coefficients for each component are higher in distillations with steam-propane than with steam. Finally, Gibbs excess energy is overall lower in distillations with steam-propane than with steam. The experimental results clearly indicate the importance of distillation on oil recovery during steam-or steam-propane injection. The experimental procedure and method of analysis developed in this study (for synthetic oil) will be beneficial to future researchers in understanding the effect of propane as steam additive on actual crude oils.Item Liquid-phase Processing of Fast Pyrolysis Bio-oil using Pt/HZSM-5 Catalyst(2013-05-01) Santos, Bjorn SanchezRecent developments in converting biomass to bio-chemicals and liquid fuels provide a promising sight to an emerging biofuels industry. Biomass can be converted to energy via thermochemical and biochemical pathways. Thermal degradation processes include liquefaction, gasification, and pyrolysis. Among these biomass technologies, pyrolysis (i.e. a thermochemical conversion process of any organic material in the absence of oxygen) has gained more attention because of its simplicity in design, construction and operation. This research study focuses on comparative assessment of two types of pyrolysis processes and catalytic upgrading of bio-oil for production of transportation fuel intermediates. Slow and fast pyrolysis processes were compared for their respective product yields and properties. Slow pyrolysis bio-oil displayed fossil fuel-like properties, although low yields limit the process making it uneconomically feasible. Fast pyrolysis, on the other hand, show high yields but produces relatively less quality bio-oil. Catalytic transformation of the high-boiling fraction (HBF) of the crude bio-oil from fast pyrolysis was therefore evaluated by performing liquid-phase reactions at moderate temperatures using Pt/HZSM-5 catalyst. High yields of upgraded bio-oils along with improved heating values and reduced oxygen contents were obtained at a reaction temperature of 200?C and ethanol/HBF ratio of 3:1. Better quality, however, was observed at 240 ?C even though reaction temperature has no significant effect on coke deposition. The addition of ethanol in the feed has greatly attenuated coke deposition in the catalyst. Major reactions observed are esterification, catalytic cracking, and reforming. Overall mass and energy balances in the conversion of energy sorghum biomass to produce a liquid fuel intermediate obtained sixteen percent (16 wt.%) of the biomass ending up as liquid fuel intermediate, while containing 26% of its initial energy.