Browsing by Subject "Solvent"
Now showing 1 - 2 of 2
Results Per Page
Sort Options
Item Improved Steam Assisted Gravity Drainage (SAGD) Performance with Solvent as Steam Additive(2011-02-22) Li, WeiqiangSteam Assisted Gravity Drainage (SAGD) is used widely as a thermal recovery technique in Canada to produce a very viscous bitumen formation. The main research objectives of this simulation and experimental study are to investigate oil recovery mechanisms under SAGD process with different injection fluids, including steam, solvent or steam with solvent. 2D simulation studies based on typical Athabasca reservoir properties have been performed. Results show that a successful solvent co-injection design can utilize the advantages of solvent and steam. There is an optimal solvent type and concentration ratio range for a particular reservoir and operating condition. Long, continuous shale barriers located vertically above or near the wellbore delay production performance significantly. Co-injecting a multi-component solvent can flush out the oil in different areas with different drainage mechanisms from vaporized and liquid components. Placing an additional injector at the top of the reservoir results only in marginal improvement. The pure high-temperature diluent injection appears feasible, although further technical and economic evaluation of the process is required. A 2D scaled physical model was fabricated that represented in cross-section a half symmetry element of a typical SAGD drainage volume in Athabasca. The experimental results show co-injecting a solvent mixture of C7 and xylene with steam gives better production performance than the injection of pure steam or steam with C7 at the study condition. Compared to pure steam injection runs ( Run 0 and 1), coinjecting C7 (Run 2) with steam increases the ultimate recovery factor of oil inside the cell from 25 percent to 29 percent and decreases the ultimate CSOR from 2.2 to 1.9 and the ultimate CEOR from 4892 J/cm 3 to 4326 J/cm 3 ; coinjecting C7 and Xylene (Run 3) increases the ultimate recovery factor of oil from 25 percent to 34 percent, and decreases the ultimate CSOR 2.2 to 1.6 and the ultimate CEOR from 4892 J/cm 3 to 3629 J/cm 3 . Analyses of the experimental results indicate that partial pressure and the near wellbore flow play important roles in production performance. In conclusion, a successful solvent injection design can effectively improve the production performance of SAGD. Further research on evaluating the performance of various hydrocarbon types as steam additives is desirable and recommended.Item Investigation of Hybrid Steam/Solvent Injection to Improve the Efficiency of the SAGD Process(2013-05-09) Ardali, MojtabaSteam assisted gravity drainage (SAGD) has been demonstrated as a proven technology to unlock heavy oil and bitumen in Canadian reservoirs. Given the large energy requirements and volumes of emitted greenhouse gases from SAGD processes, there is a strong motivation to develop enhanced oil recovery processes with lower energy and emission intensities. In this study, the addition of solvents to steam has been examined to reduce the energy intensity of the SAGD process. Higher oil recovery, accelerated oil production rate, reduced steam-to-oil ratio, and more favorable economics are expected from the addition of suitable hydrocarbon additives to steam. A systematic approach was used to develop an effective hybrid steam/solvent injection to improve the SAGD process. Initially, an extensive parametric simulation study was carried out to find the suitable hydrocarbon additives and injection strategies. Simulation studies aim to narrow down hybrid steam/solvent processes, design suitable solvent type and concentration, and explain the mechanism of solvent addition to steam. In the experimental phase, the most promising solvents (n-hexane and n-heptane) were used with different injection strategies. Steam and hydrocarbon additives were injected in continuous or alternating schemes. The results of the integrated experimental and simulation study were used to better understand the mechanism of hybrid steam/solvent processes. Experimental and simulation results show that solvent co-injection with steam leads to a process with higher oil production, better oil recovery, and less energy intensity with more favorable economy. Solvent choice for hybrid steam/solvent injection is not solely dependent on the mobility improvement capability of the solvents but also reservoir properties and operational conditions such as operating pressure and injection strategy. Pure heated solvent injection requires significant quantities. A vaporized solvent chamber is not sustainable due to low latent heat of the solvents. Alternating steam and solvent injection provides heat for the solvent cycles and increases oil recovery. Co-injection of small volumes (5-15% by volume) of suitable solvents at the early times of the SAGD operation considerably improves the economics of the SAGD process.