Browsing by Subject "Shape Memory"
Now showing 1 - 2 of 2
Results Per Page
Sort Options
Item Shape memory behavior of ultrafine grained NiTi and TiNiPd shape memory alloys(2009-05-15) Kockar, BenatThe cyclic instability in shape memory characteristics of NiTi-based shape memory alloys (SMAs), such as transformation temperatures, transformation and irrecoverable strains and transformation hysteresis upon thermal and mechanical cycling limits their applications requiring high number of cycles. The main reasons for these instabilities are lattice incompatibility between transforming phases and relatively low lattice resistance against dislocation motion. The objective of this study is to increase the slip resistance and thus, to minimize the plastic accommodation upon phase transformation in NiTi and TiNiPd SMAs. The effects of grain refinement down to submicron to nanorange through Equal Channel Angular Extrusion (ECAE) on the cyclic stability were investigated as potential remedies. The influence of ECAE parameters, such as processing temperature and strain path on the microstructural refinement was explored as well as the corresponding evolution in the stress differential between the yield strength of martensite and the critical stress to induce martensite and SMA characteristics of Ni49.7Ti50.3, Ti50Ni30Pd20, and Ti50.3Ni33.7Pd16 SMAs. Severe plastic deformation via ECAE at temperatures from 300?C up to 450?C refined the grains from 50?m down to a range between 0.03?m and 0.3?m in Ni49.7Ti50.3 and 0.5?m and 1?m in TiNiPd alloys. Regardless of the material, the lower the ECAE temperature and the higher the ECAE strain path, the better the cyclic stability. ECAE led to an increase in the stress differential between the yield strength of martensite and critical stress to induce martensite due to observed microstructural refinement and this increase is responsible for the improvement in the cyclic stability of the aforementioned SMA characteristics in all investigated materials. Addition of Pd to the NiTi alloy reduced the thermal hysteresis from 36?C down to 11?C, and enhanced the cyclic stability of the SMA characteristics. In additions to positive influence of ECAE on cyclic stability, it also led to an increase in the fracture stress levels of the TiNiPd alloys due to the fragmentation or dissolution of the precipitates responsible for the premature failures. ECAE caused a slight reduction in the work output; however it was possible to obtain large stable work outputs under higher stress levels than unprocessed materials.Item Shape memory response and microstructural evolution of a severe plastically deformed high temperature shape memory alloy (NiTiHf)(Texas A&M University, 2006-04-12) Simon, Anish AbrahamNiTiHf alloys have attracted considerable attention as potential high temperature Shape Memory Alloy (SMA) but the instability in transformation temperatures and significant irrecoverable strain during thermal cycling under constant stress remains a major concern. The main reason for irrecoverable strain and change in transformation temperatures as a function of thermal cycling can be attributed to dislocation formation due to relatively large volume change during transformation from austenite to martensite. The formation of dislocations decreases the elastic stored energy, and during back transformation a reduced amount of strain is recovered. All these observations can be attributed to relatively soft lattice that cannot accommodate volume change by other means. We have used Equal Channel Angular Extrusion (ECAE), hot rolling and marforming to strengthen the 49.8Ni-42.2Ti-8Hf (in at. %) material and to introduce desired texture to overcome these problems in NiTiHf alloys. ECAE offers the advantage of preserving billet cross-section and the application of various routes, which give us the possibility to introduce various texture components and grain morphologies. ECAE was performed using a die of 90?? tool angle and was performed at high temperatures from 500??C up to 650??C. All extrusions went well at these temperatures. Minor surface cracks were observed only in the material extruded at 500 ??C, possibly due to the non-isothermal nature of the extrusion. It is believed that these surface cracks can be eliminated during isothermal extrusion at this temperature. This result of improved formability of NiTiHf alloy using ECAE is significant because an earlier review of the formability of NiTiHf using 50% rolling reduction concluded that the minimum temperature for rolling NiTi12%Hf alloy without cracks is 700??C. The strain level imposed during one 90?? ECAE pass is equivalent to 69% rolling reduction. Subsequent to ECAE processing, a reduction in irrecoverable strain from 0.6% to 0.21% and an increase in transformation strain from 1.25% to 2.18% were observed at a load of 100 MPa as compared to the homogenized material. The present results show that the ECAE process permits the strengthening of the material by work hardening, grain size reduction, homogeneous distribution of fine precipitates, and the introduction of texture in the material. These four factors contribute in the increase of stability of the material. In this thesis I will be discussing the improvement of mechanical behavior and stability of the material achieved after various passes of ECAE.