Browsing by Subject "Phase locked loop"
Now showing 1 - 3 of 3
Results Per Page
Sort Options
Item Design of charge pump phase locked loop(2012-08) Mishra, Satyabh; Li, Changzhi; Gale, Richard O.Phase Locked Loop system is around since 1932. The versatility of PLL systems and where it can apply makes it very useful. It can be applied to automobiles as well as cellular chips. This thesis work presents design and analysis of a Phase Locked Loop in IC level. It is implemented and designed in a 0.5um CMOS process. All the blocks of the Phase Locked Loop was designed independently and then integrated together. Phase Frequency Detector, Charge Pump, Low Pass Filter, VCO, Frequency Divider and Level Shifter topologies and circuits are described in detail along with some major design tradeoffs and critical issues. The uses and implementation of two kind of frequency divider is demonstrated. Their design tradeoffs are utilized to make design effective and robustItem High performance pulse width modulated CMOS class D power amplifiers(2012-12) Lu, Jingxue; Gharpurey, RanjitThe objective of this research is to explore circuit techniques and architectures suitable for implementation in digital technologies, that can be used to enhance the efficiency of power stages. Specifically, the use of switching power stages with pulse-width modulation techniques is considered. Switching power stages, such as Class D amplifiers, are inherently well-suited for implementation in deep-submicron CMOS. Pulse-width modulation (PWM) employs discrete amplitude levels and encodes signal information in local time-based averages, and as such can also benefit from such technologies. Additionally PWM does not suffer from quantization noise, and is well-suited for low noise applications. PWM designs, that can be applied for a range of signal bandwidth requirements, spanning several tens to hundreds of kHz are proposed. Applications for these architectures include audio systems, powerline communications and wireless communications. Design challenges and requirements that can arise in different application contexts are considered in the specification of the architectures. A common goal in the definition of the architectures is to minimize complexity of the designs. In the first part of the dissertation, a third-order self-oscillating PWM class-D amplifier for audio applications, that utilizes a hysteretic comparator is described. The design is analyzed and its THD is theoretically determined by employing an equivalent model, that relates the approach to natural sampling pulse-width modulation. The architecture eliminates the requirement for a high-quality carrier generator. A low-cost hysteresis compensation technique is utilized to enhance distortion performance at high output power levels. An implementation is presented in a 0.7um CMOS process. The design achieves a dynamic range (DR) of 116.5 dB, and a THD+N of 0.0012%, while delivering a power of 125 mW into an 8[Omega] load at 1 kHz. The THD+N is under 0.006% up to 90% of the maximum output power. The amplifier can deliver 1.45 W into the load with a THD of 5% with a 5 V power supply. The efficiency is greater than 84% for output power larger than 1 W. The area of the amplifier is 6 mm². The achieved performance indicates that the design is well-suited for high-performance audio applications. A class D line driver that utilizes a phase-locked loop (PLL) based PWM generation technique is presented next. The principle of operation, and implementation details relating to loop stability, linearity and noise performance are analyzed. An implementation is presented in a 130nm CMOS process. The amplifier can deliver 1.2 W into an 6.8[Omega] load with a 4.8 V power supply. The architecture eliminates the requirement for a high-quality carrier generator and a fast, continuous voltage comparator that are often required in PWM implementations. The design can achieve a THD of -65 dB, with a switching frequency that can be as high as 20 MHz. The peak efficiency is 83% for output power larger than 1 W, for a switching frequency of 10 MHz. The area of the amplifier is 2.25 mm². This architecture is potentially suitable for powerline applications. Finally, a phase-locked loop based PWM Cartesian transmitter with the capability to drive switched power amplifiers, such as a Class D power amplifier, is proposed. A phase-locked loop based technique is employed to generate a high-frequency PWM pulse stream centered at 1.28 GHz. The prototype is simulated in a 130 nm CMOS process, and achieves 35% peak efficiency for 17 dBm output power with a carrier frequency of 900 MHz. Operation of the architecture with non-constant envelope modulation, such as that employed in the WCDMA standard, is verified in simulation.Item Oscillator Architectures and Enhanced Frequency Synthesizer(2009-11-16) Park, Sang WookA voltage controlled oscillator (VCO), that generates a periodic signal whose frequency is tuned by a voltage, is a key building block in any integrated circuit systems. A sine wave oscillator can be used for a built-in self testing where high linearity is required. A bandpass filter (BPF) based oscillator is a preferred solution, and high quality factor (Q-factor) is needed to improve the linearity. However, a stringent linearity specification may require very high Q-factor, not practical to implement. To address this problem, a frequency harmonic shaping technique is proposed. It utilizes a finite impulse response filter improving the linearity by rejecting certain harmonics. A prototype SC BPF oscillator with an oscillating frequency of 10 MHz is designed and measurement results show that linearity is improved by 20 dB over a conventional oscillator. In radio frequency area, preferred oscillator structures are an LC oscillator and a ring oscillator. An LC oscillator exhibits good phase noise but an expensive cost of an inductor is disadvantageous. A ring oscillator can be built in standard CMOS process, but suffers due to a poor phase noise and is sensitive to supply noise. A RC BPF oscillator is proposed to compromise the above difficulties. A RC BPF oscillator at 2.5 GHz is designed and measured performance is better than ring oscillators when compared using a figure of merit. In particular, the frequency tuning range of the proposed oscillator is superior to the ring oscillator. VCO is normally incorporated with a frequency synthesizer (FS) for an accurate frequency control. In an integer-N FS, reference spur is one of the design concerns in communication systems since it degrades a signal to noise ratio. Reference spurs can be rejected more by either the lower loop bandwidth or the higher loop filter. But the former increases a settling time and the latter decreases phase margin. An adaptive lowpass filtering technique is proposed. The loop filter order is adaptively increased after the loop is locked. A 5.8 GHz integer-N FS is designed and measurement results show that reference spur rejection is improved by 20 dB over a conventional FS without degrading the settling time. A new pulse interleaving technique is proposed and several design modifications are suggested as a future work.