Browsing by Subject "DC-DC converter"
Now showing 1 - 4 of 4
Results Per Page
Sort Options
Item A sigma-delta DC-DC converter(2007-12) Schulmeyer, Kyle; Chao, Kwong S.; Parten, Michael E.A switching DC-DC converter is proposed that uses a Sigma-Delta Modulator (SDM) in place of the usual Pulse Width Modulator (PWM). One type of control method, voltage mode control used for switching regulators involves sensing the output voltage to servo the loop to regulate the output. Voltage mode control has inherently bad line response, which is the ability to filter out changes on the input so they don’t reach the output. The typical method to improve this response can put more noise on the output when a steady state ripple is present. The proposed architecture provides an advantage over a PWM based converter in that it does not put as many harmonics in the low frequency range when steady state ripple is present on the input.Item DC-DC converter current source fed naturally commutated brushless DC motor drive(Texas A&M University, 2004-11-15) Khopkar, Rahul VijaykumarThe aim of this work is to reduce the cost and size of a brushless dc motor (BLDC) drive as well as increase the reliability and ruggedness of that drive. Traditional BLDC drives use Voltage Source Inverters (VSI) that utilize hard switching, thereby generating switching losses and entail the use of large heatsinks. VSI needs a huge dc link capacitor that is inherently unreliable and is one of the most expensive components of a drive. Hence, a Current Source Inverter (CSI) is used to replace the hard switchings by natural turn-off, thereby eliminating the heatsinks as well as the large dc link capacitor. A controlled rectifier together with a large inductor act as the current source. The only disadvantage is the large value of the dc link inductor and the huge number of turns needed to achieve these values of the inductances lead to huge resistive losses. Therefore, it is shown that it is possible to replace the controlled rectifier and the large inductor with a suitable dc-dc converter based current source switching at high frequencies and a much smaller value of the dc link inductor. Switching at high frequencies makes it possible to reduce the value of the dc link inductor without increasing the current ripple. Hence, it is possible to have the advantages of using a CSI as well as reduce the value of the dc link inductor without a corresponding increase in the heat sink and snubber requirements.Item Design and Implementation of Switching Voltage Integrated Circuits Based on Sliding Mode Control(2010-10-12) Rojas Gonzalez, Miguel AngelThe need for high performance circuits in systems with low-voltage and low-power requirements has exponentially increased during the few last years due to the sophistication and miniaturization of electronic components. Most of these circuits are required to have a very good efficiency behavior in order to extend the battery life of the device. This dissertation addresses two important topics concerning very high efficiency circuits with very high performance specifications. The first topic is the design and implementation of class D audio power amplifiers, keeping their inherent high efficiency characteristic while improving their linearity performance, reducing their quiescent power consumption, and minimizing the silicon area. The second topic is the design and implementation of switching voltage regulators and their controllers, to provide a low-cost, compact, high efficient and reliable power conversion for integrated circuits. The first part of this dissertation includes a short, although deep, analysis on class D amplifiers, their history, principles of operation, architectures, performance metrics, practical design considerations, and their present and future market distribution. Moreover, the harmonic distortion of open-loop class D amplifiers based on pulse-width modulation (PWM) is analyzed by applying the duty cycle variation technique for the most popular carrier waveforms giving an easy and practical analytic method to evaluate the class D amplifier distortion and determine its specifications for a given linearity requirement. Additionally, three class D amplifiers, with an architecture based on sliding mode control, are proposed, designed, fabricated and tested. The amplifiers make use of a hysteretic controller to avoid the need of complex overhead circuitry typically needed in other architectures to compensate non-idealities of practical implementations. The design of the amplifiers based on this technique is compact, small, reliable, and provides a performance comparable to the state-of-the-art class D amplifiers, but consumes only one tenth of quiescent power. This characteristic gives to the proposed amplifiers an advantage for applications with minimal power consumption and very high performance requirements. The second part of this dissertation presents the design, implementation, and testing of switching voltage regulators. It starts with a description and brief analysis on the power converters architectures. It outlines the advantages and drawbacks of the main topologies, discusses practical design considerations, and compares their current and future market distribution. Then, two different buck converters are proposed to overcome the most critical issue in switching voltage regulators: to provide a stable voltage supply for electronic devices, with good regulation voltage, high efficiency performance, and, most important, a minimum number of components. The first buck converter, which has been designed, fabricated and tested, is an integrated dual-output voltage regulator based on sliding mode control that provides a power efficiency comparable to the conventional solutions, but potentially saves silicon area and input filter components. The design is based on the idea of stacking traditional buck converters to provide multiple output voltages with the minimum number of switches. Finally, a fully integrated buck converter based on sliding mode control is proposed. The architecture integrates the external passive components to deliver a complete monolithic solution with minimal silicon area. The buck converter employs a poly-phase structure to minimize the output current ripple and a hysteretic controller to avoid the generation of an additional high frequency carrier waveform needed in conventional solutions. The simulated results are comparable to the state-of-the-art works even with no additional post-fabrication process to improve the converter performance.Item Wide input range DC-DC converter with digital control scheme(Texas A&M University, 2006-04-12) Harfman Todorovic, MajaIn this thesis analysis and design of a wide input range DC-DC converter is proposed along with a robust power control scheme. The proposed converter and its control is designed to be compatible to a fuel cell power source, which exhibits 2:1 voltage variation as well as a slow transient response. The proposed approach consists of two stages: a primary three-level boost converter stage cascaded with a high frequency, isolated boost converter topology, which provides a higher voltage gain and isolation from the input source. The function of the first boost converter stage is to maintain a constant voltage at the input of the cascaded DC-DC converter to ensure optimal performance characteristics with high efficiency. At the output of the first boost converter a battery or ultracapacitor energy storage is connected to take care of the fuel cell slow transient response (200 watts/min). The robust features of the proposed control system ensure a constant output DC voltage for a variety of load fluctuations, thus limiting the power being delivered by the fuel cell during a load transient. Moreover, the proposed configuration simplifies the power control management and can interact with the fuel cell controller. The simulation results and the experimental results confirm the feasibility of the proposed system.