Browsing by Subject "Chemical enhanced oil recovery"
Now showing 1 - 3 of 3
Results Per Page
Sort Options
Item Accounting for reservoir uncertainties in the design and optimization of chemical flooding processes(2012-08) Rodrigues, Neil; Delshad, Mojdeh; Pope, Gary A.Chemical Enhanced Oil Recovery methods have been growing in popularity as a result of the depletion of conventional oil reservoirs and high oil prices. These processes are significantly more complex when compared to waterflooding and require detailed engineering design before field-scale implementation. Coreflood experiments that have been performed on reservoir rock are invaluable for obtaining parameters that can be used for field-scale flooding simulations. However, the design used in these floods may not always scale to the field due to heterogeneities, chemical retention, mixing and dispersion effects. Reservoir simulators can be used to identify an optimum design that accounts for these effects but uncertainties in reservoir properties can still cause poor project results if it not properly accounted for. Different reservoirs will be investigated in this study, including more unconventional applications of chemical flooding such as a 3md high-temperature, carbonate reservoir and a heterogeneous sandstone reservoir with very high initial oil saturation. The goal of the research presented here is to investigate the impact that select reservoir uncertainties can have on the success of the pilot and to propose methods to reduce the sensitivity to these parameters. This research highlights the importance of good mobility control in all the case studies, which is shown to have a significant impact on the economics of the project. It was also demonstrated that a slug design with good mobility control is less sensitive to uncertainties in the relative permeability parameters. The research also demonstrates that for a low-permeability reservoir, surfactant propagation can have a significant impact on the economics of a Surfactant-Polymer Flood. In addition to mobilizing residual oil and increasing oil recovery, the surfactant enhances the relative permeability and this has a significant impact on increasing the injectivity and reducing the project life. Injecting a high concentration of surfactant also makes the design less sensitive to uncertainties in adsorption. Finally, it was demonstrated that for a heterogeneous reservoir with high initial oil saturation, optimizing the salinity gradient will significantly increase the oil recovery and will also make the process less sensitive to uncertainties in the cation exchange capacity.Item Mobility control of chemical EOR fluids using foam in highly fractured reservoirs(2011-05) Gonzaléz Llama, Oscar; Nguyen, Quoc P.; Pope, Gary A.; Mohanty, KishoreHighly fractured and vuggy oil reservoirs represent a challenge for enhanced oil recovery (EOR) methods. The fractured networks provide flow paths several orders of magnitude greater than the rock matrix. Common enhanced oil recovery methods, including gases or low viscosity liquids, are used to channel through the high permeability fracture networks causing poor sweep efficiency and early breakthrough. The purpose of this research is to determine the feasibility of using foam in highly fractured reservoirs to produce oil-rich zones. Multiple surfactant formulations specifically tailored for a distinct oil type were analyzed by aqueous stability and foam stability tests. Several core floods were performed and targeted effects such as foam quality, injection rate, injection type, permeability, gas saturation, wettability, capillary pressure, diffusion, foam squeezing, oil flow, microemulsion flow and gravity segregation. Ultimately, foam was successfully propagated under various core geometries, initial conditions and injections methods. Consequently, fluids were able to divert to unswept matrix and improve the ultimate oil recovery.Item Selection and evaluation of surfactants for field pilots(2011-05) Dean, Robert Matthew; Pope, Gary A.; Weerasooriya, UpaliChemical flooding has been studied for 50 years. However, never have the conditions encouraging its growth been as good as right now. Those conditions being new, improved technology and oil prices high enough to make implementation economical. The objective of this work was to develop economical, robust chemical formulations and processes that recover oil in field pilots when properly implemented. This experimental study goes through the process of testing surfactants to achieve optimal phase behavior, coreflooding with the best chemical formulations, improving the formulation and testing it in more corefloods, and then finally recommending the formulation to be tested in a field pilot. The target reservoir contains a light (34° API, 10 cP), non-reactive oil at about 22° C. The formation is a moderate permeability (50 - 300 mD) sandstone with a high clay content (up to 13%). Different surfactants and surfactant mixtures were tested with the oil including alkyl benzene sulfonates (ABS), Guerbet alcohol sulfates (GAS), alkyl propoxy sulfates, and internal olefin sulfonates (IOS). The best formulation contained 0.75% TDA -13PO-SO₄, 0.25% C₂₀₋₂₄ IOS, 0.75% isobutanol (IBA), 1% Na₂CO₃, all which are mixed in a softened fresh water from a supply well. Corefloods recovered 93% of residual oil from reservoir cores. Core flood experiments were also done with the alkali sodium carbonate to measure the effluent pH in a Bentheimer sandstone core with a cation exchange capacity (CEC) of 2 meq/100g. Floods at frontal velocities of 100, 10, and 0.33 ft/D were performed with 0.3 pore volume slugs of 0.7% Na₂CO₃ at 86° C. The effluent was analyzed for ions and pH breakthrough. It was found that the pH breakthrough occurred before surfactant breakthrough would be expected as desired although the pH was lower at a frontal velocity of 0.33 ft/D than at the higher velocities. The Na₂CO₃ consumption was 0.244, 0.238, and 0.207 meq/100 g rock at velocities of 100, 10, and 0.33 ft/D, respectively. In addition, a no-alkaline formulation consisting of a new large hydrophobe ether carboxylate surfactant mixed with an internal olefin sulfonate was tested on an active oil and it successfully recovered 99% of the waterflood remaining oil from an Ottawa sand pack with no salinity gradient and no alkali. The final residual oil saturation after the chemical flood (S[subscript orc]) was only 0.005